21. December 2016
Abstract Synergetic role of polymer blending on dissolution of amorphous solid dispersion was investigated. Dissolution rates of hypromellose (HPMC) and methacrylic acid copolymer (EUD) from the HPMC/EUD spray-dried sample (SPD) were improved compared to those of each single polymer SPD. Differential scanning calorimetry measurements revealed that the structural change in HPMC following heating was inhibited by co-spray-drying with EUD, suggesting an intermolecular interaction between the...
27. October 2016
Abstract The positively charged amino acids are commonly used excipients in biopharmaceutical formulations for stabilization of therapeutic proteins, yet the mechanisms for their modulation of protein stability are poorly understood. In this study, both lysine and histidine are shown to affect the thermal stability of myoglobin, bovine serum albumin, and lysozyme through a combination of mechanisms governed by their respective functional side chains and glycine, similar to arginine. This study...
08. October 2016
Abstract The number of topical fungal infections is growing, mostly owing to immunosuppressive therapy. Several topical fungal infections, such as eye mycoses, can be treated by local administration of antimycotic drugs. One major group of the antifungal agents is triazole, such as voriconazole (VCZ), which is used as the first line treatment of aspergillosis. A disadvantage of VCZ is its low water solubility making the drug difficult to administer in a liquid preparation. The lipid-based...
15. August 2016
Abstract The saturation solubility of PVP:PZQ physical mixtures (PMs) and solid dispersions (SDs) prepared from ethanol (E/E) or ethanol/water (E/W) by the solvent evaporation method at 1:1, 2:1 and 3:1 ratio (w/w) was determined. The presence of PVP improves the solubility of PZQ (0.31 ± 0.01 mg/mL). A maximum of 1.29 ± 0.03 mg/mL of PZQ in solution was achieved for the 3:1 SD (E/E). The amount of PZQ in solution depends on the amount of polymer and on the preparation method. Solid-state NMR...
27. July 2016
Granules with release-sustaining properties were developed by twin screw hot melt granulation (HMG) using a combination of stearic acid (SA) and high molecular weight polyethylene oxide (PEO) as matrix for a highly water soluble model drug, metoprolol tartrate (MPT). Earlier studies demonstrated that mixing molten SA and PEO resulted in hydrogen bond formation between hydroxyl groups of fatty acid molecules and ether groups in PEO chains. These molecular interactions might be beneficial in...
21. June 2016
Abstract Protein stability is the most crucial factor in protein pharmaceutical preparations. Various techniques were applied for producing stable protein formulations such as spray-drying and freeze-drying. However, heating and freezing stresses are disadvantages for proteins using these methods, respectively. Accordingly, excipients have been used to preserve therapeutic effects of proteins during processing and for long period of time. Therefore, influences of Copovidone, Eudragit® RL-PO...
28. May 2016
Microscale freeze-drying makes rapid process cycles possible for early-stage formulation development. To investigate the effects of equipment scale and cooling rate on the solid state properties and the protein’s secondary structure of a sample, three binary formulations of catalase were prepared and freeze-dried with sucrose, mannitol, or (2-hydroxypropyl)-β-cyclodextrin (HP-β-CD). The protein’s secondary structure was assessed using attenuated total reflection Fourier transform infrared...
16. May 2016
Paracetamol (PAR), phenylephrine hydrochloride (PHE) and chlorpheniramine maleate (CPM) are commonly used in clinical practice as antipyretic and analgesic drugs to ameliorate pain and fever in cold and flu conditions. The present work describes the use of thermal analysis for the characterization of the physicochemical compatibility between drugs and excipients during the development of solid dosage forms. Thermogravimetric analysis (TGA) and Differential Scanning Calorimetry (DSC) were used...
25. April 2016
This study consists of two experimental designs. Within the first one, suitable technique for application of model drug onto inactive pellets was evaluated and formulation and process parameters with greatest impact to process efficency and useful yield were determined. Results of experiments showed that formulation characteristics were the ones with the greatest impact on coating efficiency and that suspension layering technique was signifficantly better for drug application onto inactive...
16. February 2016
In the pharmaceutical field, solid-state transitions that may occur during manufacturing of pharmaceuticals are of great importance. The phase transition of a model API, caffeine Form I (CFI), was studied during direct compression process by analysing the impacts of the operating conditions (process and formulation). This work is focused on two formulation parameters: nature of the diluent and impact of the caffeine dilution, and one process parameter: the compression pressure that may impact...